6A Trace Width Calculator
2oz Copper | Internal Layer | IPC-2221
For 6A current on 2oz copper internal layer with 10°C temperature rise:
Input Parameters
MOD: TR_WID_V1Results
Analysis & Recommendations
Design Guidance
- •6A on Internal layer, min width: 4.65mm
- •Add 10-20% safety margin. Recommended: 5.35mm
- •Cross-sectional area: 501.89 mil² (0.3238 mm²)
Electrical Impact
- •Resistance (10mm trace): 0.55 mΩ
- •Voltage drop: 3.32 mV
- •Power dissipation: 19.92 mW
IPC-2221 Calculation Method
This calculation uses the IPC-2221 standard formula: I = k × ΔT^b × A^c where k=0.024, b=0.44, c=0.725. Internal layers use lower k-value due to reduced heat dissipation
Understanding 6A Trace Width Requirements
When designing a PCB that needs to carry 6 amperes of current, proper trace width calculation is critical for thermal management and reliability. Based on the IPC-2221 standard, a 2oz copper internal layer trace requires approximately 4.65mm (183.2 mil) width to safely handle this current with a 10°C temperature rise. This calculation ensures your printed circuit board maintains optimal performance without excessive heating, which could lead to solder joint failure, delamination, or fire hazards in extreme cases.
Key Parameters for 6A Design
- Current Capacity: 6A (amperes) - the maximum continuous current this trace is designed to carry
- Copper Weight: 2 oz/ft² (70μm) - determines the conductor cross-sectional area
- Layer Type: Internal ( sandwiched between FR4 dielectric material)
- Temperature Rise: 10°C above ambient (IPC-2221 conservative design guideline)
- Cross-Section Area: 501.89 sq mil (0.3238 mm²)
Why Layer Type Matters for 6A Current
Internal layers are sandwiched between FR4 dielectric material, which has relatively poor thermal conductivity (~0.3 W/m·K). For 6A on 2oz copper internal layer, the trace must be wider to compensate for reduced heat dissipation. The calculated width of 4.65mm is the IPC-2221 estimate for this current; confirm against your fabricator's capability and your own thermal margin.
IPC-2221 Standard Formula
The IPC-2221B standard provides the industry-accepted formula for PCB trace width calculation: I = k × ΔT^b × A^c, where I is current in amperes, ΔT is temperature rise in °C, A is cross-sectional area in square mils, and k, b, c are empirical constants specific to internal layers. This is the empirical IPC-2221 relationship this calculator implements; real boards also depend on copper thickness tolerance, airflow and neighbouring traces, so treat the result as an estimate.
6 A compared with other design choices
All figures come from the same IPC-2221 function as the calculator above, with a 100 mm run for resistance values.
| Copper | External (mm) | Internal (mm) |
|---|---|---|
| 0.5 oz | 7.15 | 18.61 |
| 1 oz | 3.58 | 9.31 |
| 2 oz | 1.79 | 4.65 |
| Rise | Width (mm) | R per 100 mm (mΩ) | Drop (mV) | Loss (mW) |
|---|---|---|---|---|
| 10 °C | 4.65 | 5.53 | 33.2 | 199 |
| 20 °C | 3.05 | 8.75 | 52.5 | 315 |
| 30 °C | 2.39 | 11.59 | 69.6 | 417 |
At the 10 °C design point a 100 mm run of this trace has 5.53 mΩ resistance (copper at 10 °C above 20 °C), drops 33.2 mV and dissipates 199 mW. Resistance, drop and loss scale linearly with trace length.
Next steps for a 6 A net: size layer-change vias for 6 A (vias need their own hole, plating and board-thickness inputs, so nothing is prefilled) or check the voltage drop of a long 6 A run.
Neighbouring currents on the same copper and layer: 5 A (3.62 mm), 8 A (6.92 mm).
Typical Applications for 6A Traces
Frequently Asked Questions
Can I use a narrower trace than 4.65mm for 6A?
Using a narrower trace will increase temperature rise beyond 10°C. While acceptable for some applications, exceeding 20-30°C rise can affect solder joint reliability and nearby component performance. Consider using thicker copper (e.g., 2oz) or parallel traces for high-reliability designs.
How does ambient temperature affect this calculation?
The IPC-2221 formula calculates temperature RISE above ambient. If your board operates in a 50°C environment with 10°C rise, the trace will reach 60°C. For high-ambient applications, design for lower temperature rise to maintain adequate safety margins.
Should I add thermal vias for 6A traces?
Thermal vias can significantly improve heat dissipation, especially for internal layer traces. For 6A and above, consider adding vias connecting to ground planes for additional thermal spreading. Use our via current calculator to properly size thermal vias.
Related Trace Width Calculations
Complete Your PCB Design
After calculating trace width for 6A, use our other free tools to complete your PCB design. Calculate via current capacity, controlled impedance for high-speed signals, and more.
Related Tools & Resources
Via Current Calculator
CalculatorCalculate via current capacity and thermal performance
Impedance Calculator
CalculatorEstimate single-ended Z0 for isolated microstrip and stripline traces. Confirm the stackup and model limits with your fabricator.
Current Capacity Calculator
CalculatorCalculate maximum safe current for PCB traces
Differential impedance reference
CalculatorReference for differential pair impedance targets and routing rules. Numeric differential calculation is temporarily unavailable while the model is validated; single-ended Z0 is available.
Pad Size Calculator
CalculatorCalculate pad diameter and area from hole size and annular ring
Thermal Relief Calculator
CalculatorDesign thermal relief patterns for soldering